Surface/material	Optimisation steps	Notes
Aluminium (AlMg3, AlMgSi1)	B and S Activating Cleaner and poss. B and S Adhesion Plus for Metal	Lightly sand with sanding fleece beforehand if necessary.
Anodised aluminium	B and S Activating Cleaner and poss. B and S Adhesion Plus for Metal	–
Steel (St 37 etc.)	B and S Activating Cleaner and poss. B and S Adhesion Plus for Metal	Lightly sand with sanding fleece beforehand if necessary. Steel components at risk of corrosion: 2-component PU or epoxy corrosion protection required.
Stainless steel (rustproof)	B and S Activating Cleaner and poss. B and S Adhesion Plus for Metal	–
Zinc-plated steel (hot-dip or zinc-plated)	B and S Activating Cleaner and poss. B and S Adhesion Plus for Metal	Lightly sand with sanding fleece beforehand if necessary.
2-component top-coat paints (PU, epoxy), 2-component water-based primers and paints, cataphoretic paints, primers (EP/2C)	B and S Activating Cleaner	Due to the large number of paints available, this information is only a guide. Where necessary, perform preliminary tests.
Powder coatings	B and S Activating Cleaner	Preliminary testing is recommended for applications involving significant forces or a damp environment.
GFRP (unsaturated polyester), gelcoat side or SMC	B and S Activating Cleaner	Lightly sand with sanding fleece beforehand if necessary.
GFRP (unsaturated polyester), layup side	1. Lightly sand with S 80 2. B and S Activating Cleaner 3. B and S Primer for P/W/S	–
ABS	1. Lightly sand with sanding fleece 2. B and S Activating Cleaner 3. B and S Primer for P/W/S	The sanding process can be omitted for parts subjected to little load.
Hard PVC	1. Lightly sand with sanding fleece 2. B and S Activating Cleaner 3. B and S Primer for P/W/S	The sanding process can be omitted for parts subjected to little load.
Glass (mineral)	B and S Activating Cleaner	Adhesive surface must be protected against UV radiation (opaque cover).
Glass ceramics	B and S Activating Cleaner	–
Untreated wood and wood products (particle board)	1. Dedusting 2. B and S Adhesion Plus for P/W/S	–
Natural stone	1. Dedusting 2. B and S Adhesion Plus for P/W/S	Can cause discolouration when used with sensitive natural stone (marble).
Concrete, mineral mortar and plasters	1. Dedusting 2. B and S Adhesion Plus for P/W/S	–
Textiles, fleeces	B and S Adhesion Plus for P/W/S	Preliminary testing required; the adhesive gripping to the fabric may be sufficient.

The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.

Application area

For removing unhardened PU or hybrid adhesives/sealants from tools and soiled, non-porous surfaces.

Instructions

Remove larger quantities of adhesive/sealant with a spatula. Either spray the remaining contamination with glue remover and wipe off with a clean cloth, or spray remover onto a cloth and wipe down the surfaces.

Adhesive remover

Variants

Thought about these?